• Network Management Card (NMC) Password Reset. The APC AP9630 UPS Network Management Card 2 allows users.
  • Recover lost password APC NetMgmt Card. Here are the steps to resetting the username and password of the APC network management cards.

Network Management Card (NMC) Password Reset Procedure. My Documents; Login/Join Partner. The AP9617 APC UPS network management card gives you full control of your power. I had to manually reset the password. I've locked myself out of an APC 9617 management card. Trying to figure out how to reset the password, or even the card to factory. How to perform a APC 9617 Reset? Environment All firmware versions (unless otherwise noted) All serial numbers; Cause The Network Management Card's administrator username and/or password has been.

Network Management Card (NMC) Password Reset Procedure. Issue. Forgotten or lost Network Management Card (NMC) Password. This article applies to Network Management Card 1 and 2, as well as any devices that contain an embedded version of these cards such as a Rack Power Distribution Unit (PDU) or Rack Automatic Transfer Switch (ATS). Product Line. Devices with an embedded Web/SNMP Card include (but are not limited to): Environmental Monitoring Unit 1 (AP9. TH)Network Management Card 1 - AP9.

AP9. 61. 8, AP9. 61. Devices with an embedded Network Management Card 1 include (but are not limited to): Metered/Switched Rack PDUs (AP7. XX, AP7. 9XX), Rack Automatic Transfer Switches (AP7. XX, Environmental Monitoring Units (AP9. AP9. 34. 0, Netbotz 2. Network Management Card 2 - AP9. AP9. 63. 0CH, AP9.

AP9. 63. 1CH, AP9. CHDevices with an embedded Network Management Card 2 include (but are not limited to): 2. G Metered/Switched Rack PDUs (AP8. XX, AP8. 6XX, AP8. XX, AP8. 9XX), Certain Audio/Video Network Management Enabled products. Browse the steps below for your device model in order to reset the administrator's password.

Note: Connecting a non- APC serial cable during the procedures below can cause unwanted erratic device behavior. Web/SNMP Card & Network Management Card 1 Procedure In addition, if you are trying to reset a password on a UPS that has more than one Smart.

Slot accessory installed in it (i. AP9. 60. 7 interface expander), it may be required to temporarily remove the other Smart. Slot accessories to gain direct serial access to the NMC console interface.

Apc Network Management Card Reset Password

Please reference that accessory's user guide on how to do that. It is also important to make sure that the accessories are installed in the correct order, referencing this document. Select a serial port at the local computer, and disable any service that uses that port.

Refer to the chart below and obtain the correct communication cable for the Network Management Card 1 enabled device: Device. Configuration Cable Part Number. Most UPSs with a DB- 9 style serial port.

Hit the reset button with the paper clip. Login with the default name apc and the password apc. Reset Mgmt Card to factory IP settings so Device IP. Can I use, after this, the APC Device IP.

DB- 9 to DB- 9)Rack PDU (AP8. XX*, AP8. 6XX*, AP8.

XX*, AP8. 9XX*, AP7. XX, AP7. 9XX)9. 40- 0. RJ- 1. 2 to DB- 9)1st Generation Rack Automatic Transfer Switch (AP7. AP7. 70. 1, AP7. 72.

DB- 9 to DB- 9)2nd Generation Rack Automatic Transfer Switch (AP7. XX, excluding 1st Generation SKUs)9. RJ- 1. 2 to DB- 9)Netbotz 2.

Environmental Monitoring (AP9. AP9. 34. 0, AP9. 32. DB- 9 to DB- 9)Rack Air Removal Unit (ACF4. ACF4. 02)9. 40- 0. DB- 9 to DB- 9). * Indicates the device uses NMC2 password reset procedure.

Connect the serial cable to the selected port on the computer and to the configuration port at the UPS/Network Management Card Embedded device. Run a terminal program (such as Hyper. Terminal. If you are unable to display the User Name prompt, verify the following. The serial port is not in use by another application. SCROLL LOCK is off/disabled.

The terminal settings are correct as specified in step 3. The correct cable is being used as specified in step 2. Press the Reset button once. The Status LED will flash rapidly (almost immediately) while alternating between orange and green. Press CTRL+C, log off, reconnect any serial cable you disconnected, and restart any service you disabled. Note: For Network Management Cards running lower than version 2.

AP9. 60. 6), step 6 (the second reset press) will not be necessary. Network Management Card 2 Procedure.

Please note: On v. X. X firmware, the Super User or Administrator level accounts can reset other Administrator, Device, Read Only, and Network Only user passwords. This procedure may not be required if the Super User password or at least one set of Administrator credentials are known. You can use a local computer that connects to the Network Management Card through the serial port to access the command line interface. This port is labeled . You'll also need to press the pinhole reset button - access is located on the front of the Network Management Card to the right of the Ethernet jack. Select a serial port at the local computer, and disable any service that uses that port.

Connect the provided serial cable (APC part number 9. Network Management Card.

Run a terminal program (such as Hyper. Terminal. If you are unable to display the User Name prompt, verify the following. The serial port is not in use by another application. SCROLL LOCK is on. The terminal settings are correct as specified in step 3. The correct cable is being used as specified in step 2.

At the local computer, select a serial port, and disable any service that uses it. Connect the serial cable from the selected port on the computer to theconfiguration port at the UPS Network Management Card or at the APC S Type.

Power Conditioner with Battery Backup. Run a terminal program (such as Hyper.

Terminal. Press ENTER, repeatedly if necessary, to display the User Name prompt. If youare unable to display the User Name prompt, verify the following. Press the Reset button.

The Status LED will flash alternately orange and green. Press the Reset button a second time immediately while the LED is flashing toreset the user name and password to their defaults temporarily.

Press ENTER as many times as necessary to redisplay the User Name prompt,then use the default, apc, for the user name and password. From the Control Console menu, select System, then User Manager. Select Administrator, and change the User Name and Password settings,both of which are now defined as apc. Sony Home Theater Manual. Press CTRL+C, log off, reconnect any serial cable you disconnected, and restartany service you disabled.

You can configure it through the UPS it's installed in via the proper APC (black) serial cable. Please don't use a generic 9- pin cable. You'll need to connect using a terminal emulation program (minicom, c. Kermit, Hyperterminal, screen, etc.). The key to doing this is stopping powerchute (or any UPS control software on the server connected to the UPS), setting the BAUD rate to 2.

You should be able to navigate the resulting text menus to gain IP information and reconfigure user names/passwords. From the documentation for the AP9. Press the Reset button. The Status LED will flash. Press the Reset button a.

LED is flashing to. Press ENTER as many times as necessary to redisplay the. User Name prompt, then use the default, apc, for the.